Ncert Solutions for Class 11 Physics Chapter 9 Pdf Download
mechanical properties of solids class 11 ncert solutions, ncert solutions, solutions of ncert, ncert solutions of, solutions ncert, ncert solut , ncert solutions, chapter 9,chapter 9ncert solutions, mechanical properties of solids ncert solutions, ncert solutions for class 11 physics, class 11 physics ncert solutions, ncert solutions for class 11, ncert class 11 physics, class 11 physics, class 11 physics solution, ncert solutions class 11, class 11 physics , ncert class 11, class 11 physics chapter 9,chapter 9 mechanical properties of solids ncert solutions
Chapter 9 Mechanical Properties Of Solids
Download NCERT Solutions for Class 11 physics
(Link of Pdf file is given below at the end of the Questions List)
In this pdf file you can see answers of following Questions
NCERT Solutions Exercises Questions
Question 9.1 A steel wire of length 4.7 m and cross-sectional area 3.0 × 10-5 m2 stretches by the same amount as a copper wire of length 3.5 m and cross-sectional area of 4.0 × 10–5 m2 under a given load. What is the ratio of the Young's modulus of steel to that of copper?
Question 9.2 Figure 9.11 shows the strain-stress curve for a given material. What are (a) Young's modulus and (b) approximate yield strength for this material?
Question 9.3 The stress-strain graphs for materials A and B are shown in Fig. 9.12.The graphs are drawn to the same scale. (a) Which of the materials has the greater Young's modulus? (b) Which of the two is the stronger material?
Question 9.4 Read the following two statements below carefully and state, with reasons, if it is true or false. (a) The Young's modulus of rubber is greater than that of steel; (b) The stretching of a coil is determined by its shear modulus.
Question 9.5 Two wires of diameter 0.25 cm, one made of steel and the other made of brass are loaded as shown in Fig. 9.13. The unloaded length of steel wire is 1.5 m and that of brass wire is 1.0 m. Compute the elongations of the steel and the brass wires.
Question 9.6 The edge of an aluminium cube is 10 cm long. One face of the cube is firmly fixed to a vertical wall. A mass of 100 kg is then attached to the opposite face of the cube. The shear modulus of aluminium is 25 GPa. What is the vertical deflection of this face?
Question 9.7 Four identical hollow cylindrical columns of mild steel support a big structure of mass 50,000 kg. The inner and outer radii of each column are 30 and 60 cm respectively. Assuming the load distribution to be uniform, calculate the compressional strain of each column.
Question 9.8 A piece of copper having a rectangular cross-section of 15.2 mm × 19.1 mm is pulled in tension with 44,500 N force, producing only elastic deformation. Calculate the resulting strain?
Question 9.9 A steel cable with a radius of 1.5 cm supports a chairlift at a ski area. If the maximum stress is not to exceed 108 N m–2, what is the maximum load the cable can support ?
Question 9.10 A rigid bar of mass 15 kg is supported symmetrically by three wires each 2.0 m long. Those at each end are of copper and the middle one is of iron. Determine the ratios of their diameters if each is to have the same tension.
Question 9.11 A 14.5 kg mass, fastened to the end of a steel wire of unstretched length 1.0 m, is whirled in a vertical circle with an angular velocity of 2 rev/s at the bottom of the circle. The cross-sectional area of the wire is 0.065 cm2. Calculate the elongation of the wire when the mass is at the lowest point of its path.
Question 9.12 Compute the bulk modulus of water from the following data: Initial volume = 100.0 litre, Pressure increase = 100.0 atm (1 atm = 1.013 × 105 Pa), Final volume = 100.5 litre. Compare the bulk modulus of water with that of air (at constant temperature). Explain in simple terms why the ratio is so large.
Question 9.13 What is the density of water at a depth where pressure is 80.0 atm, given that its density at the surface is 1.03 × 103 kg m–3?
Question 9.14 Compute the fractional change in volume of a glass slab, when subjected to a hydraulic pressure of 10 atm.
Question 9.15 Determine the volume contraction of a solid copper cube, 10 cm on an edge, when subjected to a hydraulic pressure of 7.0 × 106 Pa.
Question 9.16 How much should the pressure on a litre of water be changed to compress it by 0.10%? Additional Exercises
Question 9.17 Anvils made of single crystals of diamond, with the shape as shown in Fig.9.14, are used to investigate behaviour of materials under very high pressures. Flat faces at the narrow end of the anvil have a diameter of 0.50 mm, and the wide ends are subjected to a compressional force of 50,000 N. What is the pressure at the tip of the anvil?
Question 9.18 A rod of length 1.05 m having negligible mass is supported at its ends by two wires of steel (wire A) and aluminium (wire B) of equal lengths as shown in Fig9.15. The cross-sectional areas of wires A and B are 1.0 mm2 and 2.0 mm2, respectively. At what point along the rod should a mass m be suspended in order to produce (a) equal stresses and (b) equal strains in both steel and aluminium wires.
Question 9.19 A mild steel wire of length 1.0 m and cross-sectional area 0.50 × 10-2 cm2 is stretched, well within its elastic limit, horizontally between two pillars. A mass of 100 g is suspended from the mid-point of the wire. Calculate the depression at the midpoint.
Question 9.20 Two strips of metal are riveted together at their ends by four rivets, each of diameter 6.0 mm. What is the maximum tension that can be exerted by the riveted strip if the shearing stress on the rivet is not to exceed 6.9 × 107 Pa? Assume that each rivet is to carry one quarter of the load.
Question 9.21 The Marina trench is located in the Pacific Ocean, and at one place it is nearly eleven km beneath the surface of water. The water pressure at the bottom of the trench is about 1.1 × 108 Pa. A steel ball of initial volume 0.32 m3 is dropped into the ocean and falls to the bottom of the trench. What is the change in the volume of the ball when it reaches to the bottom?
Please Wait pdf file is loading (कृपया इंतजार करें pdf file लोड हो रही है)...
Loading speed will depend up on your download speed. Pdf file के लोड होने में लगा समय आपकी डाउनलोड स्पीड पर निर्भर करेगा
Download pdf file links for Mechanical Properties Of Solids Class 11 NCERT Solutions
To download above pdf file Link is given below.
उपर दिखायी दे रही पीडीऍफ़ को डाउनलोड करने का लिंक नीचे दिया गया है
If You have any problem/query related to above page please send us your Query to ncerthelp@gmail.com with code Serial No1517/1106. Thanks
Ncert Solutions for Class 11 Physics Chapter 9 Pdf Download
Source: https://ncerthelp.com/text.php?ques=1518+NCERT+Solutions+Class+11+Physics+Chapter+9+Download+in+Pdf